E 0 : Low Power

E 1 : Internal Error (Int)
E 2 : No I/O-voltage
E 3 : No Dump-voltage
E 5 : Parameter error
E 6 : Internal Error (Time)
E 7 : No Relay box supply voltage
E 8 : System type lost
E 9 : Internal Error (CBuf)
E 10 : Dump Output Error
E 11 : One jib sensor unconnected
E 12 : Both jib and winch connected
E 13 : Winch indicator error
E 14 : Slewing sector error
E 15 : Inner Boom Pressure error
E 16 : Jib Boom Pressure error
E 18 : Internal Error (Log)
E 19 : Micro-mode selector error
E 20 : System not running
E 21 : No Box supply voltage
E 22 : No Outer Boom Tilt Indicator
E 23 : No Inner Boom Tilt Indicator
E 24 : Outer Boom Pressure error
E 25 : Lever sensor 8 (A1) out of range
E 26 : Lever sensor 7 (A2) out of range
E 27 : Lever sensor 4 (A3) out of range
E 28 : Lever sensor 5 (A4) out of range
E 29 : Lever sensor 6 (A5) out of range
E 30 : Lever sensor 1 (A6) out of range
E 31 : Lever sensor 2 (A7) out of range
E 32 : Lever sensor 3 (A8) out of range
E 33 : Outer boom press (B1) out of range
E 34 : Outer boom tilt (B2) out of range
E 35 : Inner boom angle (B3) out of range
E 36 : Jib in pressure (B4) out of range
E 37 : Jib out pressure (B5) out of range
E 38 : Jib tilt (B6) out of range
E 39 : Winch sensors (B7) out of range
E 40 : Micro-mode input (B8) out of range
E 41 : Relay-box volt out (C1) out of range
E 42 : DUMP voltage in (C2) out of range
E 43 : DUMP-voltage out (C3) out of range
E 44 : IO-voltage in (C4) out of range
E 45 : Conn box volt out (C5) out of range
E 46 : Slew angle sensor (C6) out of range
E 47 : Temp sensor (C7) out of range
E 48 : Inner boom press (C8) out of range

E 49 : Inner Boom Angle error
E 50 : No Inner Boom Pressure Sensor
E 51 : No Outer Boom Pressure Sensor
E 52 : Lever not centered at startup
E 53 : Remote control Unit Error
E 54 : Power Supply Box Error
E 55 : Radio Receiver Error
E 56 : DA-module error
E 57 : Support legs not set
E 58 : Multiplexer 1 error
E 59 : Multiplexer 2 error
E 60 : Multiplexer 3 error
E 61 : Micro ON/OFF-switch error
E 62 : A/D-converter 1 error
E 63 : A/D-converter 2 error
E 64 : A/D-converter 3 error
E 65 : Real Time Lost
E 66 : Service Interval
E 67 : Outer Boom Angle error
E 71 : PLC Program Lost
E 72 : PLC Program Error
E 73 : PLC Error 1
E 74 : PLC Error 2
E 75 : PLC Error 3
E 76 : PLC Error 4
E 77 : Remote battery empty
E 78 : CombiDrive Error
E 80 : Analog angle sensor 1 error
E 81 : Analog angle sensor 2 error
E 82 : Analog angle sensor 3 error
E 83 : Analog angle sensor 4 error
E 84 : Lever supervision